AG101
器件资料摘要：
WJ Communications, Inc. • Phone: 1-800-WJ1-4401 • FAX: 408-577-6620 • e-mail: sales@wj.com • Web site: www.wj.com April 2002
AG101
Product Description
The AG101 is a general purpose gain block that
offers good dynamic range in a low cost surface
mount package. The combination of flat OIP3
and noise figure performance over frequency
makes it attractive for for both narrow band
and broadband applications. Superior thermal
design allows the product to achieve +32 dBm
OIP3 performance at a mounting temperature
of +85°C with an associated MTBF of >1000
years
3
. All devices are 100% RF and DC tested.
Product Features
•
60 - 3000 MHz
•
+32 dBm Output IP3
•
2.4 dB Noise Figure
•
14 dB Gain
•
+15 dBm P1dB
•
MTBF >1000 Years
•
SOT-89 SMT Package
•
Single Bias Supply
(+3.3 V or +4.5 V)
Functional Diagram
4
123
Function Pin No.
Input 1
Ground 2
Output/Bias 3
Ground 4
High Dynamic Range Gain Block
Recommended Maximum Ratings
Parameter Rating
Operating Case Temperature -40 to +85°C
Storage Temperature -55 to +125°C
DC Voltage +5.5 V
RF Input Power (continuous) +4 dBm
Operation of this device above any of these parameters may cause permanent damage.
Ordering Information
Part No. Description
AG101 GaAs MMIC Amplifier
(Available in tape and reel)
AG101-PCB Fully Assembled Application Circuit
The Communications Edge
™
Advanced Product Information
Specifications
Parameter Units Min. Typical Max.
Frequency Range MHz 60-3000
S21 - Gain dB 13.0 14.0 16.0
S11 - Input Return Loss dB -9.0
S22 - Output Return Loss dB -15.0
Output IP3 dBm +28 +32 +36
Output P1dB dBm +15
Noise Figure dB 2.4
Operating Current Range mA 40 50 75
Supply Voltage V 4.5
Test conditions unless otherwise noted.
1. T = 25°C, Vdd = 4.5 V, Frequency = 800 MHz, 50 ohm system.
2. 3OIP measured with two tones at an output power of 2 dBm/tone separated by 10 MHz. The
suppression on the largest IM3 product is used to calculate the 3OIP using a 2:1 slope rule.
3. MTBF calculated with ground lead temperature at 85°C.
4. S11 can be improved using an optional matching network.
Typical Parameters
Parameter Units Typical
Frequency MHz 900 1900
S21 dB 13.4 12.2
S11 dB -12.5 -13.2
S22 dB -21.2 -17.8
Output IP3 dBm +32.5 +33.1
Output P1dB dBm +15.1 +15.0
Noise Figure dB 2.4 2.6
Typical parameters reflect performance in an applicaton circuit.
Actual Size
AG101
Product Description
The AG101 is a general purpose gain block that
offers good dynamic range in a low cost surface
mount package. The combination of flat OIP3
and noise figure performance over frequency
makes it attractive for for both narrow band
and broadband applications. Superior thermal
design allows the product to achieve +32 dBm
OIP3 performance at a mounting temperature
of +85°C with an associated MTBF of >1000
years
3
. All devices are 100% RF and DC tested.
Product Features
•
60 - 3000 MHz
•
+32 dBm Output IP3
•
2.4 dB Noise Figure
•
14 dB Gain
•
+15 dBm P1dB
•
MTBF >1000 Years
•
SOT-89 SMT Package
•
Single Bias Supply
(+3.3 V or +4.5 V)
Functional Diagram
4
123
Function Pin No.
Input 1
Ground 2
Output/Bias 3
Ground 4
High Dynamic Range Gain Block
Recommended Maximum Ratings
Parameter Rating
Operating Case Temperature -40 to +85°C
Storage Temperature -55 to +125°C
DC Voltage +5.5 V
RF Input Power (continuous) +4 dBm
Operation of this device above any of these parameters may cause permanent damage.
Ordering Information
Part No. Description
AG101 GaAs MMIC Amplifier
(Available in tape and reel)
AG101-PCB Fully Assembled Application Circuit
The Communications Edge
™
Advanced Product Information
Specifications
Parameter Units Min. Typical Max.
Frequency Range MHz 60-3000
S21 - Gain dB 13.0 14.0 16.0
S11 - Input Return Loss dB -9.0
S22 - Output Return Loss dB -15.0
Output IP3 dBm +28 +32 +36
Output P1dB dBm +15
Noise Figure dB 2.4
Operating Current Range mA 40 50 75
Supply Voltage V 4.5
Test conditions unless otherwise noted.
1. T = 25°C, Vdd = 4.5 V, Frequency = 800 MHz, 50 ohm system.
2. 3OIP measured with two tones at an output power of 2 dBm/tone separated by 10 MHz. The
suppression on the largest IM3 product is used to calculate the 3OIP using a 2:1 slope rule.
3. MTBF calculated with ground lead temperature at 85°C.
4. S11 can be improved using an optional matching network.
Typical Parameters
Parameter Units Typical
Frequency MHz 900 1900
S21 dB 13.4 12.2
S11 dB -12.5 -13.2
S22 dB -21.2 -17.8
Output IP3 dBm +32.5 +33.1
Output P1dB dBm +15.1 +15.0
Noise Figure dB 2.4 2.6
Typical parameters reflect performance in an applicaton circuit.
Actual Size